Needs checking
Drivers are never stopped at the door over a serial number or a work report. When they can’t record something, it waits in Needs checking for the office to finish.
Each line says what happened, at which customer and stop, with which driver and vehicle, and has one action. Everything you do is recorded with your name and the time.
What you can do
Section titled “What you can do”- Finish a work report: fill in what’s missing, then number and email it.
- Close a work report without sending: when it can’t or shouldn’t go out, with a reason.
- Name cylinders a driver couldn’t: search by serial and pick the right ones.
- Check a new serial number: confirm a cylinder a driver added, or swap it for the real one.
- Check a cylinder that went out from quarantine: look at its batch and expiry, then mark it as checked.
- Check a cylinder delivered past a date: such as its expiry date, where your settings warn rather than block.
Before you start
Section titled “Before you start”Needs checking is part of Assets, which Bottle must switch on for your business.
Who can use it
Section titled “Who can use it”The Owner and Admin roles can view the list and act on every line. The Technical and Driver roles don’t see it.
Find what’s waiting
Section titled “Find what’s waiting”Open Asset register, then the Needs checking tab. The tab shows how many are waiting.
Filter by Show:
- Everything
- Work reports not finished
- Cylinders the driver couldn’t name
- New serial numbers
- Other cylinders not named
- Went out from quarantine
- Delivered past a date
Filter by When: Any time, Today, Last 7 days or Last 30 days. Clear filters shows everything again.
Finish a work report
Section titled “Finish a work report”A work report is not finished when the driver left out something your work report settings require, such as a check, the customer’s signature or the purchase order number. It has no number and hasn’t been emailed.
- Press Finish report on a Work report not finished line. Missing lists what’s needed, signatures and the purchase order number first, then checks by cylinder.
- Set any Job type that’s missing.
- Mark each check OK or Problem. Problem with Gauge (with the check’s name) needs a note.
- If you answered any check, fill in Who confirmed the checks, such as “Sam by phone at 2.15pm”. It is kept with the report.
- Fill in the Purchase order number if it’s needed.
- Press Finish and send report.
Bottle numbers the report and emails it to the customer, once, with the PDF attached. Only the report goes. The delivered email already went when the driver recorded the stop. Bottle then says “Work report 41 sent.”, or that the customer has no email address on the account, or that the email didn’t go and to try Resend on the order.
Reports missing a signature
Section titled “Reports missing a signature”The office can never add a signature or the customer’s printed name.
- If your settings require the customer’s signature and printed name, or the driver’s signature, and the report hasn’t got it, the report can’t go out. Bottle says so, links to Work report settings, and offers only Close without sending.
- If your settings don’t require the customer’s signature, the button reads Send without the customer’s signature.
Close a report without sending
Section titled “Close a report without sending”Press Close without sending, type Why it isn’t going out and confirm. The report keeps no number and the customer gets no email. It leaves the list.
Name the cylinders
Section titled “Name the cylinders”A line reads, for example, 2 cylinders not named. Under Cylinders the driver couldn’t name, it gives the driver’s reason, such as “The driver couldn’t read the labels.” Under Other cylinders not named, the stop named fewer cylinders than went through the door for another reason, such as a serial recorded somewhere else.
- Press Name the cylinders.
- Type a serial number. Bottle searches the cylinders of that product and says where each one most likely is.
- Choose the cylinders, then press Name 2 cylinders (the button counts them).
Each named cylinder moves to where the stop’s stock went: to the customer for a delivery, or onto the vehicle for a collection. Naming some leaves the rest on the list. A cylinder recorded anywhere since the stop is refused.
To leave them, press Leave unnamed and type Why they’re staying unnamed.
Check a new serial number
Section titled “Check a new serial number”When a driver types a serial Bottle hasn’t seen, Bottle adds it to the register where they found it, marked To check. The line reads New serial number C500999.
- Press Check and confirm.
- Correct its details, then press Confirm cylinder.
If it was a typing mistake, press Not a real serial number and choose what should happen:
- Swap it for the cylinder already in the register: type the serial on the cylinder, choose it, and press Swap for that serial. The real cylinder takes its place on the same stop.
- Remove it and name the cylinder later: the made-up serial is removed, and one cylinder is left to name at that stop.
Check a cylinder that went out from quarantine
Section titled “Check a cylinder that went out from quarantine”The line reads, for example, C431108 went out from quarantine. Its batch wasn’t released to full stock before a driver handed it over.
- Press Check cylinder. Bottle shows its Current details.
- Check its batch and expiry, such as with the filler.
- Add a note if you like. It is kept in the cylinder’s Movements.
- Press Mark as checked.
See Batch intake.
Check a cylinder delivered past a date
Section titled “Check a cylinder delivered past a date”The line reads, for example, C431108 delivered past a date, then “Expiry date 05/11/2026 had passed when it was delivered.” It appears when a cylinder detail’s After the date is Warn driver and office. See Cylinder details.
- Press Check cylinder. Bottle shows its Current details.
- Check the cylinder with the customer, such as swapping or collecting it.
- Add a note if you like. It is kept in the cylinder’s Movements.
- Press Mark as checked.
Undoing the stop takes the cylinder off the list.
A cylinder blocked by Driver can’t hand it over never reaches the customer. If a phone that hadn’t caught up sent it anyway, it is left off the stop and shows under Other cylinders not named, with the reason.
A work report can also wait here for “No Batch number recorded for C500110” when Serial, batch and expiry for each cylinder is ticked. Record the detail on the cylinder’s page, then finish the report.
Questions
Section titled “Questions”Does finishing a report send the delivered email again? No. The customer already had it when the driver recorded the stop. Only the report goes.
What if the driver’s phone sends the stop again after I’ve named a cylinder? The cylinder you named stays where you put it. Nothing reopens, and the report keeps its one number and one email.
Can I add the customer’s signature from the office? No. Close the report without sending, or change your work report settings if the signature isn’t needed.
If something goes wrong
Section titled “If something goes wrong”| Problem | What to do |
|---|---|
| “No customer’s signature. Your work report settings need one on every report, so this report can’t go out.” | Close the report without sending, or turn off Customer’s signature and printed name under Driver must record. |
| “No driver’s signature. Your work report settings need one on every report, so this report can’t go out.” | Close the report without sending, or turn off Driver’s signature under Driver must record. |
| “Work report 41 finished. The customer has no email address on the account, so it wasn’t sent.” | Open the order and use Resend to type an address. |
| “Work report 41 finished, but the email didn’t go. Try Resend on the order.” | Open the order and press Resend. |
| “No cylinder of this product has that serial number.” | Check the serial. Only cylinders of the stop’s product are found. |
| “Not saved. Try again.” | Check your connection and press the button again. |
| “That cylinder has been recorded somewhere since this stop. Choose another one, or leave the cylinder unnamed.” | Choose another cylinder, or press Leave unnamed and give the reason. |
| “Someone has already dealt with this. Refresh the list.” | Refresh the page. Someone else finished that line. |
| “That work report has already been finished or closed, or its stop was undone. Refresh the list.” | Refresh the page. The line has gone from the list. |
| “Say who confirmed the checks to finish the report.” | Fill in Who confirmed the checks, then press Finish and send report again. |
| “Say what the problem is with Gauge on C500110.” | Type a note under the check marked Problem. |